Online Training
CERTIFICATION COURSES
Courses are available online individually or as a complete end-to-end live training workshop for your entire company. Certification for each individual course is achieved upon successful completion of an examination at the end of each course. Achieve the “Specialist” accreditation by completing all certification courses within a track.
Safety: REQUIRED PREREQUISITE TO ALL OTHER COURSES
Fueling System Safety
General forecourt safety course including vapor and liquid management, potential site dangers, fire safety, life-saving rules, and personal protective equipment. Completion of this course is required before certification test access will be granted for any other course. This required course is FREE.
Forecourt Specialist
Containment (UPP® Brand)
UPP® tank chambers, under dispenser containment, entry seals, EBW® shear valves,, backfill materials/compaction, tightness testing, and access covers & skirts,
Pipework (UPP® Brand)
UPP® pipework theory of operation, pipe installation, fittings, entry seals, electrofusion welding, and best practices.
Submersible Pumps
FE PETRO® submersible pump model overview, theory of operation, installation, servicing, best practices, and mechanical leak detectors.
Spill Containment
Defender Series® spill container model overview, site preparation, installation, testing, maintenance, and best practices.
Overfill Prevention
EBW® Defender Series® overfill prevention valve model overview, installation, testing, and best practices including remote fill application installation. NOT VALID IN CALIFORNIA.
Stage II Vapor Recovery
HEALY™ Stage II Enhanced Vapor Recovery system and approved equipment covered under CARB Executive Orders VR-201 & VR-202. includes ORVR nozzles, hoses, vacuum sources, vapor kits, clean air separators and maintenance procedures. For markets requiring Stage II EVR.
Wire Management*
UPP® Cable-Tight™ wire management system overview, transition chambers, conduit, ducting, and entry fittings installation. *As needed for applicable markets.
Cable Tight™ System - Americas
Cable Tight™ wire management system overview for UL markets including conduit, fittings, and entry seal installation for both fiberglass and polyethylene sumps.
Containment Backfilling and Compaction
Backfilling and compaction overview including pre-backfilling requirements, material selection, compaction near piping/containment assemblies, and piping installation in backfill.
Corrosion Control™ System
Corrosion Control™ System overview of in-tank and in-sump corrosion protection. Covers assembly and installation of system components, EVO™ console programming, diagnostics, and troubleshooting information.
Defender Series™ P/V Vent
Defender Series® pressure/vacuum vent with in-line vault operational overview, installation, testing, and maintenance.
Containment (Watertight Fiberglass Tank Sump)
Fiberglass 2-piece tank sump models with integrated fill channel for sump riser to sump base installation. Covers product overview, specialized installation procedures, and testing.
Pipework and Containment (APT® Brand)
APT® pipework and APT® tank/dispenser containment sumps. Includes theory of operation, installation of products and applicable components (fittings, entry seals, valves, etc.) and best practices. Also includes FLEX-ING™ flexible connectors and pipework/containment testing procedures.
Controller Specialist
Automatic Tank Gauge Installation
EVO™ 550 & EVO™ 5000 automatic tank gauge model overview, installation (locating, mounting), modules, probes, remote alarms, turbine pump interface, and sensors.
Electronic Line Leak Detection
INCON® electronic line leak detection model overview, installation, and wiring.
In-Station Diagnostics*
INCON® in-station diagnostics model overview, installation, and wiring. *As needed for applicable markets. NOT VALID IN CALIFORNIA.
EVO™ 600 & EVO™ 6000 Installation & Wiring
EVO™ 600 and EVO™ 6000 automatic tank gauge model overview, installation and wiring of modules, probes, remote alarms, sensors, and Turbine Pump Interface
EVO™ 200 & EVO™ 400 Installation
EVO™ 200 and EVO™ 400 automatic tank gauge model overview, installation (locating, mounting), modules, probes, remote alarms, and sensors.
Fixed and Variable Speed Pump Controllers - 60Hz Markets
FE PETRO® fixed and variable speed pump controllers applicable for 60Hz markets - model overview, installation, calibration, troubleshooting, and interfacing.
Site Startup Specialist
Containment Testing
Tightness testing for UPP® containment sumps as well as the INCON™ sump test system.
Fuel Management Systems Programming
EVO™ 550 & EVO™ 5000 automatic tank gauge programming including preparation, direct connection, network interface, setup, maintenance, and troubleshooting.
Electronic Line Leak Detection
INCON® electronic line leak detection including calibration, programming, and troubleshooting.
In-Station Diagnostics Startup*
INCON® in-station diagnostics startup including programming, testing, and troubleshooting. *As needed for applicable markets. NOT VALID IN CALIFORNIA.
EVO™ 600 & EVO™ 6000 Programming
EVO™ 600 and EVO™ 6000 fuel management & system programming including user/network interfacing, console navigation, initial setup, and optional supported feature programming.
EVO™ 200 & EVO™ 400 Programming
EVO™ 200 and EVO™ 400 fuel management systems programming including preparation, direct connection, network interface, setup, maintenance, and troubleshooting.
California Air Resources Board (CARB) Certifications - For California & Applicable Markets
FMS Installation - INCON® Level 1
INCON® automatic tank gauge model overview, installation (locating, mounting), modules, probes, remote alarms, and turbine pump interface. This course is FREE.
FMS Programming - INCON® Level 2
INCON® fuel management systems programming including preparation & setup, direct connection, network interface, & maintenance/troubleshooting. This course is FREE.
Sump Test System Operation - INCON® Level 4
This course is intended for service technicians who use and maintain Franklin Fueling Systems INCON® brand sump tester, the TS-STS. This course is FREE.
Vapor Recovery Monitoring - INCON® Level 5 - VR-202/204
Vapor Recovery Monitoring (VRM) system requirements for approved equipment per CARB Executive Orders VR-202 & VR-204. Certification valid only with current FMS Installation - INCON® Level 1 and FMS Programming - INCON® Level 2 certifications. For California and applicable markets only.
HEALY™ Operator Training
This course is intended for service station attendants who oversee and maintain Franklin Fueling Systems dispenser hanging hardware products. This course is FREE.
FFS EVR Phase I Systems - VR-101
Stage I Enhanced Vapor Recovery system per CARB Executive Order VR-101. Includes spill containers, drain valves, product/vapor/riser adapters. drop tubes, overfill prevention devices, and pressure/vacuum vent valves. For California and applicable markets only.
DC400 Dispensing Cutoff System
This course is intended for technicians who are working with Franklin Fueling Systems DC400 dispensing cutoff system. This course is FREE.
Additional Training
Flexible Connectors
FLEX-ING™ flexible connectors end fittings overview, installation, and best practices.
FFS PRO Verify Site Supervisor
FFS PRO™ Verify Site Verification training reserved for designated site supervisors. Remote installation verification using web or mobile app for qualifying sites. Requires FFS PRO™ Verify program registration of applicable site.
Compliance Testing
Compliance testing procedures for EVO™ ATG, tank testing/troubleshooting, line leak detection, probes and sensors, overfill prevention, spill containment, and piping/containment tightness.
Secondary Containment Monitoring (SCM)
Secondary containment monitoring overview covering applicable containment areas, component hardware, software, and installation/operation/troubleshooting.
Flexible Probe Installation
Flexible probe installation overview covering handling, installation, wiring, and ATG programming requirements. Also includes procedures for removal and troubleshooting.